HFU620J060PALL 頗爾水過濾器
HFU640J060 PALL 頗爾水過濾器
HFU660J060 PALL 頗爾水過濾器
HFU680J060 PALL 頗爾水過濾器

HFU620J100 PALL 頗爾水過濾器
HFU640J100 PALL 頗爾水過濾器
HFU660J100 PALL 頗爾水過濾器
HFU680J100 PALL 頗爾水過濾器
HFU620J200 PALL 頗爾水過濾器
HFU640J200 PALL 頗爾水過濾器
HFU660J200 PALL 頗爾水過濾器
HFU680J200 PALL 頗爾水過濾器

流體流動的整個表面上是完全一致的

of the filter medium. This evenly distributed flow is maintained

該過濾介質。這是保持均勻流

by the flow channel being of the same width and length on

通過流動通道的相同的寬度和長度

both sides of the filter medium (see Figure 4). This uniform

過濾介質的兩側（見圖4）。這套制服

f low is maintained, even with high differential pressures

低維護，即使在高壓差

across the element, due to the uniquely designed upstream

在元，由于設計獨特的上游

support and downstream drainage layers. These layers, which

支持和下游排水層。這些層，其中

sandwich the filter medium, hold the flow channels open. The

三明治的過濾介質，保持通道開放。的

pleats are then held in place and preserved by the proprietary

褶然后舉行的地方和專有的保存

external helical wrap that is bonded to each pleat tip along

外螺旋包裝，是結合在一起的尖端沿褶

the outer diameter of the cartridge. Comparatively, the

筒的外徑。相對的，

upstream flow channel of the medium in a conventional

在傳統的中上游流道

triangular-shaped pleat structure is much more open than

三角形的褶皺結構比開放更多的

the downstream side (see Figure 5). Consequently, the flow is

下游側（見圖5）。因此，流量

highest at the bottom of the pleat. This non-uniform flow

在褶裥底最高。這種非均勻流

distribution may result in areas of rapid plugging where the

分布可能會導致地區快速堵漏的地方

flow is the highest. Additionally, such a flow pattern through

流量是最高的。此外，這種流動模式通過

a conventional triangular-shaped pleat structure may cause

傳統的三角形狀的褶皺結構可能會導致

inconsistent particle removal.

不一致的顆粒去除。